Three-dimensional-printed patient-specific instrumentation is an accurate tool to reproduce femoral bone tunnels in multiple-ligament knee injuries.

PURPOSE: Multiple-ligament knee reconstruction techniques often involve the creation of several bone tunnels for various reconstruction grafts. A critical step in this procedure is to avoid short tunnels or convergences among them. Currently, no specific template guide to reproduce these angulations has been reported in the literature, and the success of the technique still depends on the experience of the surgeon. The aim of this study is to analyze the accuracy and reliability of 3D-printed patient-specific instrumentation (PSI) for lateral and medial anatomical knee reconstructions. METHODS: Ten cadaveric knees were scanned by computed tomography (CT). Using specific computer software, anatomical femoral attachments were identified: (1) on the lateral side the lateral collateral ligament (LCL) and the popliteal tendon (PT) and (2) on the medial side the medial collateral ligament (MCL) and the posterior oblique ligament (POL). Four bone tunnels were planned for each knee, and PSI with different directions were designed as templates to reproduce the planned tunnels during surgery. Twenty 3D-printed PSI were used: ten were tailored to the medial side for reconstructing MCL and POL tunnels, and the other ten were tailored to the lateral side for reconstructing LCL and PT tunnels. Postoperative CT scans were made for each cadaveric knee. The accuracy of the use of 3D-printed PSI was assessed by superimposing post-operative CT images onto pre-operative images and analyzing the deviation of tunnels performed based on the planning, specifically the entry point and the angular deviations. RESULTS: The median entry point deviations for the tunnels were as follows: LCL tunnel, 1.88 mm (interquartile range (IQR) 2.2 mm); PT tunnel, 2.93 mm (IQR 1.17 mm); MCL tunnel, 1.93 mm (IQR 4.26 mm); and POL tunnel, 2.16 mm (IQR 2.39). The median angular deviations for the tunnels were as follows: LCL tunnel, 2.42° (IQR 6.49°); PT tunnel, 4.15° (IQR 6.68); MCL tunnel, 4.50° (IQR 6.34°); and POL tunnel, 4.69° (IQR 3.1°). No statistically significant differences were found in either the entry point or the angular deviation among the different bone tunnels. CONCLUSION: The use of 3D-printed PSI for lateral and medial anatomical knee reconstructions provides accurate and reproducible results and may be a promising tool for use in clinical practice.

Complications of standard versus long cephalomedullary nails in the treatment of unstable extracapsular proximal femoral fractures: A randomized controlled trial.

AIMS: To compare in a prospective randomized trial the mechanical complications in patients with unstable extracapsular proximal femur fractures without subtrochanteric extension (AO/OTA 31-A2 and 31-A3) METHODS: We prospectively studied 182 patients with unstable extracapsular proximal femur fractures without fractures lines extending more than 3 cm below the lesser trochanter, randomized to receive either a 'standard' (240 mm) nail or a long nail and followed them up for 1 year. RESULTS: We found no difference in the incidence of mechanical or general complications between the two groups, no cut-outs, no fractures of the tip the implant, 1 cut-through and 2 malrotations in the LN group, 2 non-unions that were reoperated, one on each group. The commonest complication was blade lateral migration, 13 (14%) patients in SN and 6 (9%) in the LN. The operating time was shorter in the SN group 51 minutes compared to 67 minutes in the LN group (p=0.000075). The mortality at 1,3 and 12 months in the SN group was of 2%, 6%, 12% while in the LN group was 12%, 18% and 22%. These differences where significative at 1 (p=0.007) and 3 months (p=0.013), but not at 12 months (p=0.075). CONCLUSIONS: We recommend the use of standard nails (240 mm) for this group of fractures, since it does not produce more mechanical complications, and it is faster, cheaper and easier to interlock distally.

A customized percutaneous three-dimensional-printed guide for scaphoid fixation versus a freehand technique: a comparative study.

The aim of this study was to compare the accuracy and reliability of percutaneous fixation of minimally displaced scaphoid fractures using a customized three-dimensional (3-D)-printed guide with a conventional freehand method. A prospective cohort of ten patients underwent scaphoid fixation with the aid of a customized 3-D-printed guide. The final screw position, total surgery time (minutes) and fluoroscopy time (seconds) was compared with a retrospective cohort of ten patients who underwent fixation with a conventional technique. There were no differences in final screw position between both methods. The patients in which the 3-D guide was used had a surgery time reduction of 43% and a fluoroscopy time reduction of 52% compared with the control freehand group. The use of a customized 3-D-printed guide permits a fixation that is as accurate as the standard freehand technique, with reduction in surgical time and intraoperative radiation exposure.Level of evidence: III.

3D printing innovation: New insights into upper extremity surgery planning.

INTRODUCTION: Surgical planning relies on the use of images to develop an action plan prior to the actual surgical intervention. Imaging technology improvement together with the development of specific software to treat three dimensional images has increased the accuracy and capabilities of pre-surgical planning. In addition to this, 3D printing allows us to manufacture customized surgical tools to implement and aid in the success of surgeries. MATERIAL AND METHODS: 3D virtual planning together with 3D printing has been implemented through different approaches in 8 different upper extremity trauma cases. We describe these 8 cases (2 women and 6 men with ages ranging from 16 to 67 years), their specific challenges and management. RESULTS: We show how 3D technology changes the conception, planning and execution of surgery in 8 different cases. In addition, we describe what challenges were faced as well as the various utilities of 3D technology beyond that of anatomical model printing. CONCLUSIONS: The use of 3D technology has improved and enhanced surgical planning. It allows us to view and virtually manipulate fracture fragments prior to surgery. It also enables us to develop customized surgical tools and guides that can increase the accuracy of certain procedures, and help in the management of orthopaedic and trauma lesions. We believe that the use of this technology is beneficial to both the patient and surgeon, since it reduces surgical time and complications giving a better understanding of the injury and its treatment.

"Can patients learn how to reduce their shoulder dislocation?" A one-year follow-up of the randomized clinical trial between the Boss-Holzach-Matter self-assisted technique and the Spaso method.

OBJECTIVE: The aim of this study was to assess the effectiveness and reproducibility of self-assisted Boss-Holzach-Matter (BHM) technique compared with the Spaso (Sp) method for shoulder dislocation. METHODS: We conducted a follow-up at 1 year from the randomization of 60 patients with shoulder dislocation enrolled in the study "Teaching patients to reduce a shoulder dislocation." Half of these patients had been taught the self-assisted technique, whereas the other half had been treated by a physician's manipulative maneuver for reduction. We surveyed all the enrolled patients to describe recurrence rates and reproducibility for both the techniques without supervision as well as the number of emergency visits. RESULTS: In total, 52 patients (age range: 18-44 years) answered the survey from the 60 patients enrolled in the study. The total rate of recurrence was 38.5% (20 patients). For the Sp group, 4 of the 30 patients were lost. There were 9 recurrent patients (30%), and 7 were treated in the emergency department (ED). For the BHM group, 4 of the 30 patients were lost. There were 11 recurrent patients (37%), and 2 were treated in the ED. The difference in self-reduction rates and ED visits for both the groups was statistically significant (p=0.025). CONCLUSION: Teaching the BHM technique to the patients is effective and reproducible without direct supervision. It can decrease the number of visits to the ED and is a valid option to teach the patients at risk of recurrence when not being able to get immediate help. LEVEL OF EVIDENCE: Level I, Therapeutic study.

Integrated 3D printing solution to mitigate shortages of airway consumables and personal protective equipment during the COVID-19 pandemic.

BACKGROUND: To cope with shortages of equipment during the COVID-19 pandemic, we established a nonprofit end-to-end system to identify, validate, regulate, manufacture, and distribute 3D-printed medical equipment. Here we describe the local and global impact of this system. METHODS: Together with critical care experts, we identified potentially lacking medical equipment and proposed solutions based on 3D printing. Validation was based on the ISO 13485 quality standard for the manufacturing of customized medical devices. We posted the design files for each device on our website together with their technical and printing specifications and created a supply chain so that hospitals from our region could request them. We analyzed the number/type of items, petitioners, manufacturers, and catalogue views. RESULTS: Among 33 devices analyzed, 26 (78·8%) were validated. Of these, 23 (88·5%) were airway consumables and 3 (11·5%) were personal protective equipment. Orders came from 19 (76%) hospitals and 6 (24%) other healthcare institutions. Peak production was reached 10 days after the catalogue was published. A total of 22,135 items were manufactured by 59 companies in 18 sectors; 19,212 items were distributed to requesting sites during the busiest days of the pandemic. Our online catalogue was also viewed by 27,861 individuals from 113 countries. CONCLUSIONS: 3D printing helped mitigate shortages of medical devices due to problems in the global supply chain.

Partial Versus Total Trapeziectomy With Interposition Arthroplasty for Trapeziometacarpal Osteoarthritis Grade II to III Eaton-Littler: A Clinical Trial.

Purpose: Total trapeziectomy is the most widely used technique to treat isolated thumb trapeziometacarpal joint osteoarthritis. However, this technique has been associated with proximal migration of the thumb metacarpal, which has led some physicians to consider partial trapeziectomy as a valid alternative. The purpose of this study was to assess whether partial trapeziectomy improves final key pinch strength compared with total trapeziectomy. Methods: We randomized 34 patients with basal thumb osteoarthritis into 2 groups to undergo partial or total trapeziectomy with interposition arthroplasty. Key pinch strength at 12 months was the primary outcome measure. Other variables measured included trapezial space height, range of motion, grip strength, change in key pinch strength, patient-reported outcome measures, and pain. Results: No difference between groups was detected regarding final pinch strength, trapezial space height, grip strength, range of motion, change in pinch strength, patient-reported outcomes (Quick-Disabilities of the Arm, Shoulder, or Hand), or pain. Conclusions: We cannot conclude that partial trapeziectomy provides an advantage over total trapeziectomy at 1 year after surgery. Although trapeziometacarpal space was substantially preserved in the partial trapeziectomy group at 12 months, this difference was not statistically or clinically significant. Type of study/level of evidence: Diagnostic III.

Long-Term Evaluation Following Partial Trapeziectomy and Suspension Arthroplasty for Trapeziometacarpal Osteoarthritis: An Observational Study.

Purpose: Partial trapeziectomy is performed to decrease the risk for first ray collapse. However, the incidence of scaphotrapezoidal (ST) joint osteoarthritis (OA) in the presence of advanced trapeziometacarpal joint OA is around 40%. The purposes of this study were to analyze the progression of the ST joint after partial trapeziectomy and to establish the potential link between radiographic findings and patient outcomes. Methods: We reviewed a series of 22 patients (26 thumbs) with base of the thumb OA who underwent partial trapeziectomy and interposition arthroplasty. Standardized radiographs of the ST joint were classified by 2 independent observers. Measured outcomes were pain, mobility (degrees of abduction, Kapandji score, and anteversion [in centimeters]), force (in kilograms]) and the short version of the Disabilities of the Arm, Shoulder, and Hand questionnaire score. Results: Median follow-up was 8 years. The modified Eaton-Glickel scale was used to rate the degree of ST joint arthritis: 2 thumbs were classified as grade 1, 11 as grade 2, 12 as grade 3, and 1 as grade 4. No parameters analyzed demonstrated a statistically significant correlation between patients' outcomes and joint radiographic arthritis. Conclusions: Our study cannot demonstrate that the radiographic presence of ST arthritis correlates with the patient's main symptoms after partial trapeziectomy. Type of study/level of evidence: Therapeutic IV.